Drywall in the CRD: When “Clean” Isn’t Enough—How to Prove Post-1990 or Asbestos-Free, and Where to Take It

November 10, 2025

 For building owners and facility managers on Vancouver Island (Victoria to Nanaimo)

Why this matters for you

If you own or manage a healthcare, school or residential facility in the Capital Regional District (CRD) or the nearby mid-island, you’re probably used to the ongoing mix of “renovation” and “demolition” work. That means drywall—removal, disposal, replacement—often is part of the job. But there’s a hidden complication: drywall (or more precisely the joint-mud and tape) installed before about 1990 may contain asbestos. And if you treat that material the same as regular clean waste, you open up risks: worker exposure, regulatory violations, disposal rejection, fines, project delays.

Here’s the reality in plain language:

  • If your drywall was installed after 1990 and you have credible proof, you may treat it as “clean” waste and dispose accordingly.
  • If it was installed before 1990, or you don’t have proof, assume it could contain asbestos. Then you must follow asbestos-waste protocols (testing, packaging, waste manifesting).
  • If you skip the steps, you’ll pay more (disposal fees), and possibly fines: for example, CRD fines for improper asbestos disposal jump to $1,000 per infraction in 2025. Victoria News
  • The regional landfill route for the CRD is the Hartland Landfill (#1 Hartland Ave, Saanich/Victoria) which sets specific policies around drywall, pre/post-1990, and asbestos. Capital Regional District

In short: you’ll save money, reduce risk and minimise headache if you prove your drywall is post-1990 or asbestos-free, and follow the correct disposal path.

How did we get here

The back-story helps you understand why this is so important (and why 1990 is the magic year).

  • According to the Canadian Labour Congress and building-materials historians, widespread use of asbestos in building products (including drywall joint-compound) tapered off in the early 1990s.
  • The provincial regulator WorkSafeBC notes that although gypsum board itself is relatively safe, “old drywall mud and some gypsum boards can contain asbestos.” WorkSafeBC
  • Under the provincial Hazardous Waste Regulation (HWR), any waste containing asbestos is “controlled waste” and must be managed accordingly (manifesting, approved landfill, sealed packaging) if coming from institutional/commercial sources. Government of British Columbia
  • At the Hartland facility, policies distinguish between “clean renovation/demolition waste” and suspect drywall (pre-1990 or unknown) or asbestos-containing waste. Capital Regional District
  • A disposal-guide published for the Central Saanich/RD area states: “Drywall installed pre-1990 may have asbestos in the tape and joint compound.” CSRD BC

In short: The industry has long recognised the risk. For facility owners and building managers this means—don’t assume your drywall is safe just because it looks like typical gypsum. Validate it.

Step 1: Prove your drywall is post-1990 (and therefore likely asbestos-free)

If you can show the drywall and joint compound were installed after 31 December 1989, you can (in many cases) treat it as clean waste rather than controlled asbestos waste. But you’ll need documentation and you’ll still need to dispose of it via the correct route. Here’s how:

  1. Check your records: building permits, inspection reports, renovation invoices, original drywall billings. If the installation date is clearly after 1990, you’re in good shape.
  2. Check the product itself: Some drywall sheets bear date-stamps, manufacturer identifiers or bar codes. For example the Regional District of Nanaimo guidance says the drywall load must have multiple date-stamps (back of sheets) dated 1 Jan 1991 or newer. RDN
  3. Use an asbestos declaration form: Many regional districts require you to sign a form declaring that your waste is post-1990 and asbestos-free (or meets criteria). For example the CRD “Reno & Demolition Waste” page references that materials must be proven non-asbestos via lab results or proven installed after 1990. Capital Regional District
  4. Keep the proof on file: When you deliver the load to Hartland or other facility, staff may ask for that proof. You don’t want to be turned away or charged higher “controlled waste” rates.

By doing this you can treat the drywall as a “normal” renovation/demolition load rather than high-risk asbestos waste. That means lower cost, fewer special procedures, less schedule disruption.

Step 2: If your drywall is pre-1990 (or date unknown) — assume it may contain asbestos

If you cannot prove the installation date is post-1990, you must act as if asbestos risk is present. The consequences of handling improperly are serious: worker exposure, regulatory liability, steep disposal fees.

Here’s your checklist:

  • Engage a qualified asbestos professional. Under the BC OHS Regulation a “qualified person” must assess asbestos hazards. WorkSafeBC
  • Obtain bulk sampling and lab analysis if you want to prove “asbestos-free”. (Otherwise default to controlled-waste procedures). For gypsum drywall, the joint compound (“mud”) and tape are common locations for asbestos. The Metro Vancouver handout says: “If before 1990, have the drywall tape and joint compound tested for asbestos”. Metro Vancouver
  • Label and double-bag/contain the material during removal. Many guidelines say pre-1990 drywall must be sealed in 6-mil polyethylene bags or other sealed containment. Government of British Columbia
  • Use a licensed abatement contractor. Especially in institutional settings (healthcare, schools, residential facilities), you need formal removal protocols. The asbestos FAQ states that as of Jan 1 2024, all asbestos abatement contractors in BC must be licensed. WorkSafeBC
  • Arrange for disposal as asbestos-containing waste. In the CRD region, the Hartland Landfill accepts asbestos waste by appointment only, properly prepared and documented. Capital Regional District

From a practical facility-manager perspective: if you’re doing demo on a building built before 1990 (many on Vancouver Island are), budget for the additional cost and schedule implications of asbestos protocols rather than assuming you’re in the clear.

Step 3: Where to take it (and how the disposal path works in the CRD and mid-island)

Here’s what you need to know for the Victoria-to-Nanaimo region:

For the CRD / Greater Victoria region (including Saanich, Oak Bay, Langford):

  • The Hartland Landfill (#1 Hartland Ave, Saanich) is operated by the Capital Regional District. Capital Regional District
  • Clean, non-asbestos renovation/demolition waste can be accepted under the “Reno & Demo Waste” program, provided the load meets the conditions: you prove either the material is non-asbestos (e.g., lab results) or installed post-1990. Capital Regional District
  • Asbestos waste (or suspect asbestos drywall) is accepted only by appointment, must meet packaging, manifesting, permit requirements. Capital Regional District
  • Disposal rates matter: the “Rates & Accepted Items” page shows asbestos/controlled waste fees are higher than standard garbage/refuse. Capital Regional District
  • Disposal is subject to fines: the CRD’s bylaw increases for improper disposal from $200 to $1,000 per infraction as of 2025. Victoria News

For the mid-island region (Nanaimo, Duncan, CVRD):

  • In the Cowichan Valley Regional District (CVRD) area, the “Construction & Demolition Waste” page states asbestos-containing materials must be properly prepared. Cowichan Valley Regional District
  • For drywall disposal in Nanaimo/RDN, the regional district guidance similarly treats drywall installed pre-1990 as suspect. RDN

Key takeaway for facility owners/managers:
Make sure your disposal chain understands whether your drywall is considered “clean” or “controlled/asbestos-suspect”. A misclassified load can result in being turned away at the scale, paying higher fees, or facing regulatory enforcement.

Step 4: Practical checklist for building owners/facility managers

Here’s how you should approach your next drywall removal/renovation project:

  • ✅ Check building age & records. If the drywall was installed after Dec 31 1989 (and you have proof), mark that as “post-1990”.
  • ✅ Visual verification. If sheets bear date-stamps, manufacturer labels, bar codes indicating post-1990 manufacture, that strengthens your case.
  • ✅ If age is uncertain or pre-1990 → assume asbestos risk. Budget accordingly.
  • ✅ Hire a qualified asbestos surveyor if needed (especially for large facilities, schools or healthcare buildings). Contractor should be licensed for asbestos abatement.
  • ✅ Ensure removal protocols are written & clear: containment, dust control, seals, PPE, negative-air, etc (refer to WorkSafeBC Safe Work Practices). WorkSafeBC
  • ✅ Prepare disposal packaging properly: For suspect loads, double bags, 6-mil polyethylene, labelled, sealed.
  • ✅ Contact Hartland (or relevant regional landfill) ahead of time: book appointment, get permit if required (for asbestos loads).
  • ✅ File your documentation: asbestos survey results, proof of installation date, disposal receipts, chain of custody. These protect you from future liability.
  • ✅ Track costs: You’ll likely pay more for suspect/asbestos loads (higher tipping fees, special handling). Avoid surprise cost overruns.
  • ✅ Review tenant/occupant safety & communications. If the building is occupied (schools, healthcare, residences) then managing occupant risk, dust migration, shutdown logistics must be built into your plan.

Step 5: What building owners tend to get wrong

Here are common pitfalls I’ve seen in 25 + years in the field:

  • Assuming gypsum board is always safe. Many think “it’s just drywall—why worry?” But the joint-mud/tape layer prior to 1990 often included asbestos. CSRD BC
  • Lack of documentation. “We don’t have the permits or inspection reports… we’ll just dispose it as normal.” That leads to rejection at the landfill or fines.
  • Under-budgeting for disposal costs. If you mis-classify the material as clean waste but it is suspect, the tipping fees rise and you may face enforcement.
  • Using unlicensed contractors. Asbestos abatement is regulated; using non-certified people exposes you to liability and regulatory breach. WorkSafeBC
  • Improper packaging of suspect loads. For instance, disposing loose pre-1990 drywall without containment is unacceptable in many districts. CSRD BC
  • Ignoring occupant safety and disturbance planning. Even if drywall is non-asbestos, the dust and particulates from sanding or removal can trigger silica, fibreglass, mould risks. The WorkSafeBC drywall guidance warns about dust, silica and asbestos. WorkSafeBC

Final thoughts

For building owners and facility managers from Victoria to Nanaimo, the takeaway is simple but vital: Don’t treat drywall removal as low-risk unless you’ve verified it. The age of the material, the documentation you hold, the destination landfill’s policies—they all matter. When you skip the verification step you’re leaving yourself exposed to cost overruns, project delays and regulatory risk.

But when you do treat it correctly—you’ll have more certainty. You’ll show tenants/occupants you’re managing hazard responsibly. You’ll save money on disposal. And you’ll avoid the surprise of a landfill refusing a load or fines being issued.

Got Questions?

We understand the stress, and confusion that dealing with hazardous materials brings. We're here to help. Got questions? Concerns? or just need to vent (pun intentional) - give us a shout!
Get in Touch

More About What We Do

Member Profile
Member Profile
Certified Asbestos Inspectors
Healthcare Construction
Certificate of Recognition
Better Business Bureau
BC Environment Ind. Association
Power System Safety Protection
AHERA® Certified
We maintain a respectful workplace environment. Ethical, Experienced, & Insured
Canadian HAZ-MAT Environmental Ltd.
Located at 3388 Douglas St. Victoria, BC V8Z 3L3 - All mail to 1111 Tulip Ave, Victoria, BC V8Z-7Z2Site Designed, Developed, & Promoted by MullerConsulting
menuchevron-down